国产精彩免费视频_色婷婷五月综合激情中文字幕_99久久免费看精品国产一区_99电击抽搐潮喷视频_成年人视频免费在线_嫩草黄页

Hello, welcome to the Jiangsu Ideal Valve Co., Ltd. official website!
TEL:+86-515-87214888      EMAIL:fnjslxfy@163.com      

Valve electric actuator 6 principles of selection!

Time:2018-09-29
Usually, the correct choice of valve electric actuator is as follows:1. Operating Torque: Operating Torque is the most important parameter to select the valve electric device. The output torque of ...

Usually, the correct choice of valve electric actuator is as follows:

1. Operating Torque: Operating Torque is the most important parameter to select the valve electric device. The output torque of the electric actuator should be 1.2-1.5 times of the maximum operating torque of the valve.

2. There are two kinds of main engine structure for operating thrust valve electric device: one is not equipped with thrust disc to output torque directly; the other is equipped with thrust disc, and the output torque is converted to output thrust through the stem nut in the thrust disc.

3. Number of rotating turns of output shaft: The number of rotating turns of output shaft of valve electric device is related to the nominal diameter of valve, the pitch of valve stem and the number of threaded head. It should be calculated according to M=H/ZS (M is the total number of rotating turns to be satisfied by electric device, H is the opening height of valve, S is the pitch of valve stem drive thread, Z is the number of valve stem threaded head).

4. Stem diameter to multi-turn open stem valve, if the maximum stem diameter allowed by the electric device can not pass through the valve stem, it can not be assembled into an electric valve. Therefore, the inner diameter of the hollow output shaft of the electric device must be larger than the outside diameter of the stem of the valve. For partial rotary valves and hidden-rod valves in multi-rotary valves, although the problem of passing through the stem diameter is not considered, the stem diameter and the key groove size should also be fully considered in the selection, so that the assembly can work properly.

5. output speed: if the valve's opening and closing speed is too fast, it will cause water hammer. Therefore, appropriate opening and closing speed should be selected according to different operating conditions.

6. valve electric actuator has its special requirement that it must be able to limit torque or axial force. Usually, valve actuators adopt a torque limiting coupling. When the specifications of the electric device are fixed, the control torque is determined. Normally running in a predetermined time, the motor will not be overloaded.

However, the following situations may lead to overload:

First, the power supply voltage is low, and the torque needed is not obtained, so that the motor stops rotating.

Secondly, the torque limiting mechanism is misadjusted to make it larger than the stop torque, resulting in continuous excessive torque, so that the motor stops rotating.

The three is intermittent use, resulting in heat storage, exceeding the allowable temperature appreciation of the motor.

Four, because of some reason, the torque limiting mechanism circuit fails, causing the torque to be too large.

Five is to use the environment temperature too high, relative to the motor heat capacity drop.

In the past, fuses, over-current relays, thermal relays, thermostats and so on were used to protect motors, but each method had its advantages and disadvantages. Absolutely no reliable protection measures are available for electric installations. Therefore, it is necessary to adopt a variety of combinations, summed up in two ways: one is to judge the increase or decrease of the input current of the motor; the other is to judge the excitation of the motor itself. These two ways, regardless of the type, must consider the time allowance given by the motor thermal capacity.

Generally, the basic protection methods for overload are:

1. overload protection for continuous operation or point operation of motor, using thermostat;

2. to protect the motor from blocking, thermal relay is adopted.

3. for short circuit accidents, fuse or overcurrent relay are used.

主站蜘蛛池模板: 久久成人精品一区二区三区 | 日韩美女一级毛片 | 国产精品福利91 | 久久极品视频 | 麻豆一区二区三区蜜桃免费 | 97国产成人精品视频 | 日本高清不卡视频 | 国产精品色在线 | 免费国产片在线观看 | 国产又色又爽又黄又免费 | 色站在线 | 亚洲精品在线观 | 九色porny丨首页原版 | 久久精国 | 久久久久久久国产精品 | 国产精品美女久久久久网站 | 99热手机在线| 米奇777第4色狠狠 | 欧美第一视频 | 成人影院www在线观看 | 久久中文字幕视频 | 亚洲射情| 欧美日韩在线中文字幕 | av观看成片免费网站 | 91麻豆精品国产91久久久更新时间 | 在线播放 亚洲 | 久草99| 青青草视频网站 | 蝌蚪777 | 大地资源高清播放在线观看视频 | 亚洲日产精品一二三四区 | 亚洲精品成人自拍 | 91在线视频精品 | 91社在线播放 | 国产做爰一区二区三区视频 | 国产免费一区二区三区免费视频 | 国产乱了真实在线观看 | 大内密探零零性性在线观看 | 91国内免费视频 | 欧美日产一区二区三区在线观看 | 国产精品福利一区二区三区 |